Rod-Tech-Talk

Marten · Marten

OK, so I think I goy my cooling stuff figured out. Thanks for the calls from a couple of guys on this site. Noticed my oil is dark so I think I should change it. what do I need to look out for? Higher compression small block Chevy for those that need that info. About 400 hp. the existing oil filter is a Mob...

Marten · Marten

Looks like I got hosed on my cooling system. I need to get a new sensor and electric fan. Running a 350 with 400 hp. What should I run for a sensor cut in, cut out temperature? Any brands I should use or avoid? Need a puller fan as well, mine doesn't move enough air. Tested things last night, not a water pump pu...

Marten · Marten

Thinking of switching from carb to fuel injection. Any suggestions on complete kits. Reviews are all over the map. I would like something that looks like a carb.

Marten · Marten

Just starting to play with this idea. My header collector is 2". Should I continue with a complete 2" exhaust or go bigger? Motor puts out 400 hp and the same in torque.

Marten · Marten

Here is a picture of my A/C and alternator and power steering. The belts in the picture are wrong, it was to check and see if it looked right. I am wondering what is the best way to have the belts. Option # 1 one belt goes from the A/C to the crank to the water pump and back to the A/C. That is the line of groove...

Cuddles · Cuddles

https://www.youtube.com/watch?v=o4HlFZkkxiI Above is the site for a video instructing how to remove and install a distributor which appears to be made for a novice like myself. I find it very helpful in understanding why, not just learning what to do. However, at 4 minutes into the video, they s...

stang · stang

Just installed 1/4 inch insulation on the floor & firewall ( inside ) Now I'm looking for insulation for the engine compartment side. Lots of products out there just wondering if anyone has any ideas or best product for the job, Thanks

Cuddles · Cuddles

Hello: I have been trying to make tight bends in fuel line for my gas tank breather line. So far I purchased two different pipe benders but they don't make tight bends. Long story short - I found a way. Perhaps a lot of old hands here know of better ways but this works too. I took a short length of metal fu...

Marten · Marten

I installed my steering shafts onto my corvette rack and pinion. Thought I had it all lined up. Everything worked was very happy until I turned the steering wheel lock to lock. One way I get 1 1/4 rotations and the other way I get 1 1/8 rotations. If I adjust the rods that go to the spindles to match the r...

Cuddles · Cuddles

Can anyone tell me if it is possible to buy individual spark plug cables ? I need 2 cables 35" or 34" long. The two I have on my 289 are a bit too snug. I have NGK blue silicone cables presently. Thank you

Cuddles · Cuddles

Hello: Is there a check list I could follow to ensure I have done all the correct things to ensure my car is properly set for winter in a cold garage ? I know I should put the car on dollies so the rubber is off the concrete and I plan to take the battery in the house and charge it once a month. What else should...

wuga · wuga

I am currently looking at a 74 F250 with a FT360 and 3 spd automatic. The motor has 45K miles on it. It is all original with the two barrel. If this comes to pass, I want to leave the engine pretty well stock but would like to get better gas mileage. I would consider changing to FiTech two barrel EFI. Has...

Matchless · Matchless

Hi everyone. I'm hoping to change over the front end on our Falcon( Comet next) to the "Granada/Comet disc brake" front suspension.I know there are lots of sites online and lots of posts on H.A.M.B. regarding what spindle/ rotor/ caliper/ etc to use but I was really hoping someone here has first hand...

58chev · 58chev

alright folks, looking for ideas on making a body dolly. Pictures if you have any, would be greatly appreciated. I need to lift the body off the chassis but be able to roll the chassis out from under it. Body does not have the front clip on it. but engine is sitting on the chassis. I am a bit lost as to what t...

Cuddles · Cuddles

My niece lives in the London Dorchester area and needs someone to bring her father's corvette back to condition for a safety. She took it to a Ford Dealership and they said she needs: Headlamp vacuum doors repaired - play in steering box - heater blower no defrost - rear wheel berrings - turn signal / h...

toomuchjunk · toomuchjunk

https://www.rodauthority.com/news/whats-gear-ratio-find-out/

Cuddles · Cuddles

I nearly lost the end of a finger fighting with the filler hose from Canadian Tire. It's reinforced with steel and doesn't bend easily. I see there is clear 2" fuel filler hose at a site called KAR TEK. Is it safe or legal to use that type of hose? It doesn't appear to be reinforced at all. Does anyone r...

Marten · Marten

I think I messed up again. Does it matter where in the fuel system the fuel filter goes? Between the tank and fuel pump or between the pump and the carb? I have the mechanical fuel pump if that makes any difference.

Cuddles · Cuddles

Can anyone help me please? I have a universal fuel gauge sending unit from Princess Auto. The only way I could get the unit into the tank was to bend the thin metal rod on which the float sits. But now that the unit is in the tank, I doubt it will give me a true reading because I had to bend the rod. The probl...

Cuddles · Cuddles

I made a couple of spark plug cable covers like I saw at the show but some of my cables fit a bit tight. Can I buy cables of different lengths individually ? Some of my wires now are a bit sloppy and some too tight (short).

Beans · Beans

Good Morning Everyone, I've been reading a lot lately about superchargers. I have a question.... Is compression just plain compression and doesn't matter how it got there?. Does a bottom end know in which way the compression was achieved? For example if you have a blown motor with a static compressi...

wuga · wuga

got it Thank you Warren -- Edited by wuga on Friday 18th of January 2019 04:45:00 PM

wuga · wuga

I have a couple of places in mind, but who east of Toronto would you recommend to rework the head on my 261? Warren

Beans · Beans

Who's there? Chunks of my timing gear. I had a minor knocking noise since I bought the car and finally pulled the pan off to have a look at things. Considering it's an engine with no oil filter I kinda thought it's quite clean inside. Pan had some sludge but there's suppose to be some in there. But I was scro...

wuga · wuga

Does anyone have a machine for arcing brake shoes or know anyone who does, preferably in eastern Ontario? Thanks Warren

wuga · wuga

I have a 1962 Cutlass which is built on a unibody chassis similar to a Corvair. I want to put a tow hitch on it so I can have a traditional vehicle to tow my Bantam altered. The package with trailer weighs under 3000 lbs. Has anyone had experience with such an install and can they lead me to a good fabricat...

cheyenne · cheyenne

I am thinking about installing a after market fan shroud in the '64 Ford, has anyone had any issues with the install, or with the after market shrouds at all once installed,..?? I am just a little leery of those nylon straps ( I have both round and flat ) and especially shoving them through a 4 core rad for...

Cuddles · Cuddles

Hello: I am hoping to install a vinyl roof on my model A Tudor. I am hoping someone here has experience and can offer advice on which steps to follow. I bought the vinyl and the turnbuckles. Now I just need to know the tips and tricks to get it right.

admin · admin

and now hot rodding is dead

cheyenne · cheyenne

https://www.facebook.com/arthur.watts.507/videos/1341881352588817/

Sub Forum	Topics	Posts	Last Post
Engine, Cooling, Carbs, fuel injection, Heads, Exhaust Everything engine, casting numbers and cooling systems here	28	103	Jul 23, 2020 by Cuddles
Transmission, clutch, Differential, drive shaft, Steering, Suspension, wheels, tires, brakes Suspension, Steering, Brakes, Wheels, Tires, Transmission, Clutch, Automatic Trans, Drive Shafts, yokes, Differential, Posi, Ratios	35	158	Aug 24, 2019 by 54vicky
Electrical, Lighting, Ignition systems, Charging systems, Heating & Air conditioning	14	63	Apr 22, 2021 by henrystoys

Topic		Started By	Replies	Views	Last Post
	oil (Preview) OK, so I think I goy my cooling stuff figured out. Thanks for the calls from a couple of guys on this site. Noticed my oil is dark so I think I should change it. what do I need to look out for? Higher compression small block Chevy for those that need that info. About 400 hp. the existing oil filter is a Mob...	Marten	3	583	Aug 1, 2022 by wuga
	Cooling system (Preview) Looks like I got hosed on my cooling system. I need to get a new sensor and electric fan. Running a 350 with 400 hp. What should I run for a sensor cut in, cut out temperature? Any brands I should use or avoid? Need a puller fan as well, mine doesn't move enough air. Tested things last night, not a water pump pu...	Marten	2	502	Jul 28, 2022 by Marten
	Fuel injection (Preview) Thinking of switching from carb to fuel injection. Any suggestions on complete kits. Reviews are all over the map. I would like something that looks like a carb.	Marten	7	925	Oct 14, 2021 by Chris Stapley
	exhaust sizing (Preview) Just starting to play with this idea. My header collector is 2". Should I continue with a complete 2" exhaust or go bigger? Motor puts out 400 hp and the same in torque.	Marten	4	849	Feb 21, 2021 by wuga
	pulleys and belts (Preview) Here is a picture of my A/C and alternator and power steering. The belts in the picture are wrong, it was to check and see if it looked right. I am wondering what is the best way to have the belts. Option # 1 one belt goes from the A/C to the crank to the water pump and back to the A/C. That is the line of groove...	Marten	9	949	Nov 26, 2020 by Marten
	distributor removal/install (Preview) https://www.youtube.com/watch?v=o4HlFZkkxiI Above is the site for a video instructing how to remove and install a distributor which appears to be made for a novice like myself. I find it very helpful in understanding why, not just learning what to do. However, at 4 minutes into the video, they s...	Cuddles	8	1065	Aug 21, 2020 by Cuddles
	Firewall Insulation (Preview) Just installed 1/4 inch insulation on the floor & firewall ( inside ) Now I'm looking for insulation for the engine compartment side. Lots of products out there just wondering if anyone has any ideas or best product for the job, Thanks	stang	4	876	Jul 19, 2020 by stang
	making tight bends (Preview) Hello: I have been trying to make tight bends in fuel line for my gas tank breather line. So far I purchased two different pipe benders but they don't make tight bends. Long story short - I found a way. Perhaps a lot of old hands here know of better ways but this works too. I took a short length of metal fu...	Cuddles	5	923	Jun 24, 2020 by Chris Stapley
	rack and pinion question (Preview) I installed my steering shafts onto my corvette rack and pinion. Thought I had it all lined up. Everything worked was very happy until I turned the steering wheel lock to lock. One way I get 1 1/4 rotations and the other way I get 1 1/8 rotations. If I adjust the rods that go to the spindles to match the r...	Marten	3	797	Apr 21, 2020 by Lightspeed Mike
	longer spark plug cables (Preview) Can anyone tell me if it is possible to buy individual spark plug cables ? I need 2 cables 35" or 34" long. The two I have on my 289 are a bit too snug. I have NGK blue silicone cables presently. Thank you	Cuddles	7	880	Mar 6, 2020 by Cuddles
	winter storage check list (Preview) Hello: Is there a check list I could follow to ensure I have done all the correct things to ensure my car is properly set for winter in a cold garage ? I know I should put the car on dollies so the rubber is off the concrete and I plan to take the battery in the house and charge it once a month. What else should...	Cuddles	14	1043	Nov 29, 2019 by Cuddles
	Ford FT 360 (Preview) I am currently looking at a 74 F250 with a FT360 and 3 spd automatic. The motor has 45K miles on it. It is all original with the two barrel. If this comes to pass, I want to leave the engine pretty well stock but would like to get better gas mileage. I would consider changing to FiTech two barrel EFI. Has...	wuga	5	783	Nov 6, 2019 by Cuddles
	One of this winter's projects - I hope (Preview) Hi everyone. I'm hoping to change over the front end on our Falcon( Comet next) to the "Granada/Comet disc brake" front suspension.I know there are lots of sites online and lots of posts on H.A.M.B. regarding what spindle/ rotor/ caliper/ etc to use but I was really hoping someone here has first hand...	Matchless	4	922	Oct 2, 2019 by Matchless
	need ideas for a body dolly (Preview) alright folks, looking for ideas on making a body dolly. Pictures if you have any, would be greatly appreciated. I need to lift the body off the chassis but be able to roll the chassis out from under it. Body does not have the front clip on it. but engine is sitting on the chassis. I am a bit lost as to what t...	58chev	9	1070	Sep 28, 2019 by Chris Stapley
	recommendation (Preview) My niece lives in the London Dorchester area and needs someone to bring her father's corvette back to condition for a safety. She took it to a Ford Dealership and they said she needs: Headlamp vacuum doors repaired - play in steering box - heater blower no defrost - rear wheel berrings - turn signal / h...	Cuddles	1	894	Sep 23, 2019 by rochie
	Rear End gearing (Preview) https://www.rodauthority.com/news/whats-gear-ratio-find-out/	toomuchjunk	0	811	Sep 9, 2019 by toomuchjunk
	fuel filler line (Preview) I nearly lost the end of a finger fighting with the filler hose from Canadian Tire. It's reinforced with steel and doesn't bend easily. I see there is clear 2" fuel filler hose at a site called KAR TEK. Is it safe or legal to use that type of hose? It doesn't appear to be reinforced at all. Does anyone r...	Cuddles	5	1025	Aug 11, 2019 by Cuddles
	fuel filter (Preview) I think I messed up again. Does it matter where in the fuel system the fuel filter goes? Between the tank and fuel pump or between the pump and the carb? I have the mechanical fuel pump if that makes any difference.	Marten	10	1241	Aug 1, 2019 by Slim
	fuel gauge sending unit (Preview) Can anyone help me please? I have a universal fuel gauge sending unit from Princess Auto. The only way I could get the unit into the tank was to bend the thin metal rod on which the float sits. But now that the unit is in the tank, I doubt it will give me a true reading because I had to bend the rod. The probl...	Cuddles	9	1120	Jul 25, 2019 by Cuddles
	spark plug cables (Preview) I made a couple of spark plug cable covers like I saw at the show but some of my cables fit a bit tight. Can I buy cables of different lengths individually ? Some of my wires now are a bit sloppy and some too tight (short).	Cuddles	4	853	Jul 17, 2019 by Cuddles
	Supercharging vs NA Compression ratios (Preview) Good Morning Everyone, I've been reading a lot lately about superchargers. I have a question.... Is compression just plain compression and doesn't matter how it got there?. Does a bottom end know in which way the compression was achieved? For example if you have a blown motor with a static compressi...	Beans	2	986	Mar 26, 2019 by Beans
	a measurement request- got it (Preview) got it Thank you Warren -- Edited by wuga on Friday 18th of January 2019 04:45:00 PM	wuga	0	918	Jan 17, 2019 by wuga
	Head work (Preview) I have a couple of places in mind, but who east of Toronto would you recommend to rework the head on my 261? Warren	wuga	7	1367	Nov 25, 2018 by shag766
	Model A - Knock Knock (Preview) Who's there? Chunks of my timing gear. I had a minor knocking noise since I bought the car and finally pulled the pan off to have a look at things. Considering it's an engine with no oil filter I kinda thought it's quite clean inside. Pan had some sludge but there's suppose to be some in there. But I was scro...	Beans	8	1129	Jul 31, 2018 by 51 Styline
	arcing brake shoes (Preview) Does anyone have a machine for arcing brake shoes or know anyone who does, preferably in eastern Ontario? Thanks Warren	wuga	10	1319	Jul 15, 2018 by 33 guy
	tow hitch (Preview) I have a 1962 Cutlass which is built on a unibody chassis similar to a Corvair. I want to put a tow hitch on it so I can have a traditional vehicle to tow my Bantam altered. The package with trailer weighs under 3000 lbs. Has anyone had experience with such an install and can they lead me to a good fabricat...	wuga	4	1081	May 10, 2018 by wuga
	Fan Shroud (Preview) I am thinking about installing a after market fan shroud in the '64 Ford, has anyone had any issues with the install, or with the after market shrouds at all once installed,..?? I am just a little leery of those nylon straps ( I have both round and flat ) and especially shoving them through a 4 core rad for...	cheyenne	20	2126	Mar 16, 2018 by Matchless
	cloth top install (Preview) Hello: I am hoping to install a vinyl roof on my model A Tudor. I am hoping someone here has experience and can offer advice on which steps to follow. I bought the vinyl and the turnbuckles. Now I just need to know the tips and tricks to get it right.	Cuddles	4	1321	Mar 16, 2018 by Beans
	hot Rod to Rat Rod.. the story.. (Preview) and now hot rodding is dead	admin	0	1059	Feb 19, 2018 by admin
	Top Quality Peace Of Mind Right Here !! (Preview) https://www.facebook.com/arthur.watts.507/videos/1341881352588817/	cheyenne	1	1068	Dec 21, 2017 by tc
1 2 3 > Last» \| Page of 3 sorted by