Electrical, Lighting, Ignition systems, Charging systems, Heating & Air conditioning

51 Styline · 51 Styline

Does anyone have a suggestion on what to use for a neutral switch for my 51 Chev. Its got a 350 tranny with a Lokar shifter in it. With the borders closed the US is not viable option. I thought there might be a factory switch that can be adapted. Just thought i,d put this out there. The old Chevettes had a...

54vicky · 54vicky

I posted a problem I have in the daily driver forum posting here to draw more eyes rather than write it over again appreciate any help

54vicky · 54vicky

I am looking for information on replacing my stock points with a hall effect trigger.what I need is to hear from anyone who has done it.I do not want theories on doing it but facts from someone who has done it.the only thing I want to change is the points NOT the coil etc.I think it should be a simple task I ju...

ThatChevyGuy · ThatChevyGuy

So after struggling for a while, giving up and coming back to it, I just finished up wiring my cruise control on the 85C10 with the 5.3L in it. This will only apply to a drive by wire throttle body motor. Essentially, theres 5 wires to make this work. Super easy. My problem was a broken brake switch on my tru...

Falcon Futura · Falcon Futura

New style fuel gauges to old age fuel senders! I am using Omega Custom Gauges in my 1965 Falcon and originally when I put the car together I cut a hole in the original fuel tank to install the matching fuel level sender unit that came with the kit. The empty ohm reading for the new style gauge is 240 ohms and...

Homer · Homer

I am installing a FiTeck 30003 go street EFI in my 34 which has a 1986 302 mustang engine in it.My problem is that I put in a electronic ignition in it what it has to have .They say that I must remove the resister out of the coil line as it does not supply the 12 volts that the coil and distributor now needs.The r...

Atomsplitter · Atomsplitter

I bought a spool of copper #2 AWG booster cable wire at an auction the other day and I was wondering if there's a "rule of thumb" for the length of cable based on the wire gauge?

henrystoys · henrystoys

Here is a front park/ signal light diagram that 2d_willys on the HAMB posted for me. For some reason it will not load here? In the park lamp wire add a 20ohm, 1W resistor and in both wires add a # 1N4001 diode. Use a 1129 or an 81 bulb

Chevy Girl · Chevy Girl

does anyone have an opinion as to whether or not use the supplied silicone grease between the module and distributor base? Does this cause a heat sinc problem? This is on my 70 Chevelle 396

58chev · 58chev

All kinds of good information... http://www.madelectrical.com/electrical-tech.shtml

Homer · Homer

I have a IC Dynamics remote model 2RTA mine will not work but the wifes will, I replaced the battery but will still not work.I sent an email to them but no answer. Can any one tell me who can repair it. Homer

henrystoys · henrystoys

http://www.camaros.net/techref/ftecref14.html

FLEET 51 · FLEET 51

HI GUYS : I'm running a G.M. HEI in my 250 INLINE but my tach doesn't work -- I don't know anything about that stuff and would appreciate any tips on how to check it out -- Thanks in Advance -- LATER -- DON / FLEET 51

admin · admin

http://www.lindertech.com/bhrs/chev_8_dist_elec_conv.htm

Topic		Started By	Replies	Views	Last Post
	Neutral Safety Switch. (Preview) Does anyone have a suggestion on what to use for a neutral switch for my 51 Chev. Its got a 350 tranny with a Lokar shifter in it. With the borders closed the US is not viable option. I thought there might be a factory switch that can be adapted. Just thought i,d put this out there. The old Chevettes had a...	51 Styline	2	658	Apr 22, 2021 by henrystoys
	changing PCM (Preview) I posted a problem I have in the daily driver forum posting here to draw more eyes rather than write it over again appreciate any help	54vicky	0	717	Aug 24, 2019 by 54vicky
	pointless ignition (Preview) I am looking for information on replacing my stock points with a hall effect trigger.what I need is to hear from anyone who has done it.I do not want theories on doing it but facts from someone who has done it.the only thing I want to change is the points NOT the coil etc.I think it should be a simple task I ju...	54vicky	5	797	Jul 24, 2019 by 54vicky
	GM LS Engines Drive By Wire Cruise Control Hookup w/ Diagram (Preview) So after struggling for a while, giving up and coming back to it, I just finished up wiring my cruise control on the 85C10 with the 5.3L in it. This will only apply to a drive by wire throttle body motor. Essentially, theres 5 wires to make this work. Super easy. My problem was a broken brake switch on my tru...	ThatChevyGuy	1	1073	Mar 24, 2018 by Lightspeed Mike
	Matching fuel gauge to fuel level sender for accuracy (Preview) New style fuel gauges to old age fuel senders! I am using Omega Custom Gauges in my 1965 Falcon and originally when I put the car together I cut a hole in the original fuel tank to install the matching fuel level sender unit that came with the kit. The empty ohm reading for the new style gauge is 240 ohms and...	Falcon Futura	0	1180	Jan 23, 2017 by Falcon Futura
	I need electrical help (Preview) I am installing a FiTeck 30003 go street EFI in my 34 which has a 1986 302 mustang engine in it.My problem is that I put in a electronic ignition in it what it has to have .They say that I must remove the resister out of the coil line as it does not supply the 12 volts that the coil and distributor now needs.The r...	Homer	9	1857	Dec 10, 2016 by Homer
	Booster Cables: Gauge vs Length? (Preview) I bought a spool of copper #2 AWG booster cable wire at an auction the other day and I was wondering if there's a "rule of thumb" for the length of cable based on the wire gauge?	Atomsplitter	5	1680	Dec 1, 2016 by shag766
	How to wire a single bulb for park/ signal usage (Preview) Here is a front park/ signal light diagram that 2d_willys on the HAMB posted for me. For some reason it will not load here? In the park lamp wire add a 20ohm, 1W resistor and in both wires add a # 1N4001 diode. Use a 1129 or an 81 bulb	henrystoys	0	1134	Nov 18, 2016 by henrystoys
	Installation of a ignition control module in a HEI distributor (Preview) does anyone have an opinion as to whether or not use the supplied silicone grease between the module and distributor base? Does this cause a heat sinc problem? This is on my 70 Chevelle 396	Chevy Girl	6	1542	Sep 12, 2016 by Supernash
	ELECTRICAL TECH (Preview) All kinds of good information... http://www.madelectrical.com/electrical-tech.shtml	58chev	1	1280	May 17, 2016 by tc
	Remote for keyless entry (Preview) I have a IC Dynamics remote model 2RTA mine will not work but the wifes will, I replaced the battery but will still not work.I sent an email to them but no answer. Can any one tell me who can repair it. Homer	Homer	4	1397	May 13, 2016 by admin
	Alternator conversion (Preview) http://www.camaros.net/techref/ftecref14.html	henrystoys	2	1288	May 3, 2016 by 58chev
	Checking tach connection on G M HEI (Preview) HI GUYS : I'm running a G.M. HEI in my 250 INLINE but my tach doesn't work -- I don't know anything about that stuff and would appreciate any tips on how to check it out -- Thanks in Advance -- LATER -- DON / FLEET 51	FLEET 51	11	2420	May 1, 2016 by FLEET 51
	Converting a small-GM points Dizzy to electronic.. (Preview) http://www.lindertech.com/bhrs/chev_8_dist_elec_conv.htm	admin	3	1977	Apr 24, 2016 by Falcon Futura
Page 1 of 1 sorted by