Transmission, clutch, Differential, drive shaft, Steering, Suspension, wheels, tires, brakes

GMDad · GMDad

I have had an issue with the fluid leaking out of the T5 in my pickup truck for quite a while now so finally pulled it out to see what the issue is. Thought it was the front collar but turns out to be the "plug" below it. Now this looks like a normal frost plug but after watching some you tubes on this trans I find...

ThatChevyGuy · ThatChevyGuy

I have the transmission that came with my 1968 Camaro. Its apparently rebuilt, but I havent pulled the cover yet to find out. I can get the exact numbers but it is not a M22 for sure. Whats a rebuild one of these going for now days? Anyone looking to buy one? Thanks a lot

toomuchjunk · toomuchjunk

http://www.rodauthority.com/tech-stories/drivetrain/10-bolt-chevy/

Beans · Beans

Looks like the throttle valve (the valve in the valve body connected to the TV Cable on the carb) is stuck or stickink. Put the truck away working great then went to drive and shifted competely different next day. Late and hard 1-2 shift. Didn't drive much else put it away right away to figure out what was...

TIME TRAVELLER · TIME TRAVELLER

I volunteer at a military museum that has a tired M114 Armoured Personnel Carrier. These were built by Cadillac in the early 60’s and originally used a 283 SBC with the old four speed Hydramatic transmission. We’re using a stock 350 but the original transmission is toast. Does anyone have, or kno...

Grumper · Grumper

I'm not sure if I'm putting this in the right section, but I'm looking for a shop that shortens driveshafts. Preferably in the K-W or London areas. Thanks

henrystoys · henrystoys

http://www.fordmuscle.com/archives/2006/02/Steelies/

Falcon Futura · Falcon Futura

Here is a great link for anyone that has changed their axle ratio or have gone to very large tires. With this link you can enter in the info to calculate which is the correct speedo gear for your transmission to keep the speedometer accurate. I have used a number of times so far. http://www.tciauto.com...

admin · admin

admin · admin

Atomsplitter · Atomsplitter

So my boy is selling his 2003 Honda Civic SI Coupe and we were wondering what the thickness of the rotors and pad material needs to be to pass a certification these days. Is there some data base I can look up to get the required thickness for this car to pass? Is it a formula based on the original thick...

58chev · 58chev

What are you guys using to lube parts of the brake caliper and back of pads? I need to do the brakes on my wife's Mazda3 and before I start would like to have everything on hand. I have read that synthetic will take higher heat than dino grease and is safer on rubber components.

shag766 · shag766

when i have seen someone asking for input pertaining to whether they should consider buying one of these tranny's or not i have mentioned that they are a good tranny with the o/d option but if they were thinking some track time with the car i wouldn't recommend this tranny. i have one in my 69 hemi corone...

slab · slab

Just looking for some opinions on Posi or not posi. Some back ground info. The rear end in my 1999 classic style 1/2 ton 2wd pick up broke(4 teeth gone on the ring and the pinion flops around like it has no bearing left and who knows what might be missing off of it). The truck had a tow package and came with a 3...

Atomsplitter · Atomsplitter

I have a chrome shift lever for a late 1960's 4 speed Ford (Mustang?) but I can't tell if it's a 1968 or not and it doesn't have any part number or markings on it. My shift lever has slots for the reverse lockout (should look like a disc below the shift knob if it's a '68) in a vertical position to the shaft (i...

Janies dirty 37 · Janies dirty 37

So I had some 22" rims given to me but they are without centre caps. I checked/ asked great google gods using any numbers/ info stamped on inside but can't come up with nodda! they are a multi fit bolt pattern for dodge truck/ car. If I can find centre caps for them that would be ideal. Or get some fabbed up?...

admin · admin

http://www.stockcarracing.com/techarticles/scrp_0711_brake_deglazing/

Beans · Beans

Is a gm - gbody kinda master cylinder backwards from most aftermarket master cylinders? Here's how my truck was plumbed. The 1/4" tube farthest from the firewall is going to the rear of the proportion valve. Is that correct for this master cylinder and proportion valve? When I look up pictures online...

Grumpy50 · Grumpy50

Ran into a issue this morning with an employee repairing his locker ass'y and over-torquing the bolts here is a basic chart for such matters - Saturday night before the races is no time for looking for the bolts ya just sheared from over-torquing . This is maybe on another thread somewhe...

Atomsplitter · Atomsplitter

So I'm in need of some new rear shocks for my '48 1/2 ton. My spec's: - 1982-94 S10 leafs springs (4 leafs, 3/1, 2.5" wide = 1350lb springs: probably a bit tired!). - truck weighs 3200lbs on the original frame. - 1985 Camaro 10 bolt rear. - XP7 upper mount & L1/CP3 lower mount (I know these shocks...

58chev · 58chev

http://www.pontiacpower.org/BW.htm

Marten · Marten

Just about ready to move forward again. I think that I need to install hoses next. For a 700R4 trans what do I ask for in cooler lines. I know where they go in but what size/type of fitting do I need? Should I use hard lines or flex?

admin · admin

admin · admin

admin · admin

According to my 1975 Chevrolet Factory Issued Service Manual for Chevelle, Camaro, Monte Carlo, Nova, and full size Chevrolet, it goes through a 4 plus page detailed explanation of the PS pump and the pressure relief valves and the 2 relief valve springs. Long story short, the small spring and ball c...

toomuchjunk · toomuchjunk

Not a big thing but kind of handy if you need a taller,shorter or wider tire http://www.discounttire.com/dtcs/infoTireMath.do TMJ

admin · admin

henrystoys · henrystoys

http://www.carnut.com/specs/index.html

henrystoys · henrystoys

https://www.rsracing.com/TechWheel.aspx

henrystoys · henrystoys

http://www.carnut.com/specs/rear.html

Topic		Started By	Replies	Views	Last Post
	Leaking T5 transmission (Preview) I have had an issue with the fluid leaking out of the T5 in my pickup truck for quite a while now so finally pulled it out to see what the issue is. Thought it was the front collar but turns out to be the "plug" below it. Now this looks like a normal frost plug but after watching some you tubes on this trans I find...	GMDad	1	802	Aug 24, 2019 by 54vicky
	Whats a Muncie worth? (Preview) I have the transmission that came with my 1968 Camaro. Its apparently rebuilt, but I havent pulled the cover yet to find out. I can get the exact numbers but it is not a M22 for sure. Whats a rebuild one of these going for now days? Anyone looking to buy one? Thanks a lot	ThatChevyGuy	4	859	Nov 3, 2018 by ThatChevyGuy
	GM rear diff. info and identification (Preview) http://www.rodauthority.com/tech-stories/drivetrain/10-bolt-chevy/	toomuchjunk	1	810	Mar 19, 2018 by 51 Styline
	Stuck Throttle Valve? 700r4 (Preview) Looks like the throttle valve (the valve in the valve body connected to the TV Cable on the carb) is stuck or stickink. Put the truck away working great then went to drive and shifted competely different next day. Late and hard 1-2 shift. Didn't drive much else put it away right away to figure out what was...	Beans	0	1533	Sep 15, 2017 by Beans
	4 SPD HYDRAMATIC TRANNY (Preview) I volunteer at a military museum that has a tired M114 Armoured Personnel Carrier. These were built by Cadillac in the early 60’s and originally used a 283 SBC with the old four speed Hydramatic transmission. We’re using a stock 350 but the original transmission is toast. Does anyone have, or kno...	TIME TRAVELLER	0	1074	May 12, 2017 by TIME TRAVELLER
	Where To Get A Driveshaft Shortened (Preview) I'm not sure if I'm putting this in the right section, but I'm looking for a shop that shortens driveshafts. Preferably in the K-W or London areas. Thanks	Grumper	7	1547	Apr 13, 2017 by rochie
	making your own custom width rims (Preview) http://www.fordmuscle.com/archives/2006/02/Steelies/	henrystoys	3	1276	Jan 11, 2017 by wuga
	Changing your axle gears or big tires? Check your speedo gear for correct speedometer reading. (Preview) Here is a great link for anyone that has changed their axle ratio or have gone to very large tires. With this link you can enter in the info to calculate which is the correct speedo gear for your transmission to keep the speedometer accurate. I have used a number of times so far. http://www.tciauto.com...	Falcon Futura	1	1141	Jan 3, 2017 by Falcon Futura
	How an automatic transmission works. (Preview)	admin	0	1236	Jan 1, 2017 by admin
	Manual transmission operation (Preview)	admin	0	1187	Jan 1, 2017 by admin
	Brake Rotor/Pad Measurement for Certification? (Preview) So my boy is selling his 2003 Honda Civic SI Coupe and we were wondering what the thickness of the rotors and pad material needs to be to pass a certification these days. Is there some data base I can look up to get the required thickness for this car to pass? Is it a formula based on the original thick...	Atomsplitter	22	2399	Dec 29, 2016 by shag766
	Brake Service Lube (Preview) What are you guys using to lube parts of the brake caliper and back of pads? I need to do the brakes on my wife's Mazda3 and before I start would like to have everything on hand. I have read that synthetic will take higher heat than dino grease and is safer on rubber components.	58chev	9	1816	Dec 27, 2016 by 51 Styline
	tko 5 spd info, maybe ?? (Preview) when i have seen someone asking for input pertaining to whether they should consider buying one of these tranny's or not i have mentioned that they are a good tranny with the o/d option but if they were thinking some track time with the car i wouldn't recommend this tranny. i have one in my 69 hemi corone...	shag766	2	1375	Dec 23, 2016 by henrystoys
	To Posi or not to Posi....that is the question! (Preview) Just looking for some opinions on Posi or not posi. Some back ground info. The rear end in my 1999 classic style 1/2 ton 2wd pick up broke(4 teeth gone on the ring and the pinion flops around like it has no bearing left and who knows what might be missing off of it). The truck had a tow package and came with a 3...	slab	4	1481	Dec 4, 2016 by Falcon Futura
	Any owners of a 1968 Mustang on this site? or people who know thier Ford stuff? (Preview) I have a chrome shift lever for a late 1960's 4 speed Ford (Mustang?) but I can't tell if it's a 1968 or not and it doesn't have any part number or markings on it. My shift lever has slots for the reverse lockout (should look like a disc below the shift knob if it's a '68) in a vertical position to the shaft (i...	Atomsplitter	8	1800	Oct 1, 2016 by Atomsplitter
	Any way to tell what brand rims are ? (Preview) So I had some 22" rims given to me but they are without centre caps. I checked/ asked great google gods using any numbers/ info stamped on inside but can't come up with nodda! they are a multi fit bolt pattern for dodge truck/ car. If I can find centre caps for them that would be ideal. Or get some fabbed up?...	Janies dirty 37	7	1613	Sep 4, 2016 by Chevy Dan
	Good article on Brake Pad and Rotor deglazing (Preview) http://www.stockcarracing.com/techarticles/scrp_0711_brake_deglazing/	admin	7	1884	Jun 23, 2016 by parklane
	GM/Aftermarket Universal Mastercylinder Question (Preview) Is a gm - gbody kinda master cylinder backwards from most aftermarket master cylinders? Here's how my truck was plumbed. The 1/4" tube farthest from the firewall is going to the rear of the proportion valve. Is that correct for this master cylinder and proportion valve? When I look up pictures online...	Beans	27	4099	Jun 14, 2016 by 58chev
	Basic Bolt Torque Spec's (Preview) Ran into a issue this morning with an employee repairing his locker ass'y and over-torquing the bolts here is a basic chart for such matters - Saturday night before the races is no time for looking for the bolts ya just sheared from over-torquing . This is maybe on another thread somewhe...	Grumpy50	4	1593	Jun 12, 2016 by admin
	Shocks for Bullwinkle??? (Preview) So I'm in need of some new rear shocks for my '48 1/2 ton. My spec's: - 1982-94 S10 leafs springs (4 leafs, 3/1, 2.5" wide = 1350lb springs: probably a bit tired!). - truck weighs 3200lbs on the original frame. - 1985 Camaro 10 bolt rear. - XP7 upper mount & L1/CP3 lower mount (I know these shocks...	Atomsplitter	3	1654	Jun 9, 2016 by Lightspeed Mike
	Borg Warner Second Design ST-10 4-Speed Info (Preview) http://www.pontiacpower.org/BW.htm	58chev	0	1312	Jun 7, 2016 by 58chev
	Tranny cooler lines (Preview) Just about ready to move forward again. I think that I need to install hoses next. For a 700R4 trans what do I ask for in cooler lines. I know where they go in but what size/type of fitting do I need? Should I use hard lines or flex?	Marten	6	2019	May 27, 2016 by 58chev
	Limited slip differential..GM locking differential (Preview)	admin	0	1378	May 14, 2016 by admin
	Hydralic Steering principals of operation (Preview)	admin	0	1225	May 14, 2016 by admin
	GM power steering pumps. (Preview) According to my 1975 Chevrolet Factory Issued Service Manual for Chevelle, Camaro, Monte Carlo, Nova, and full size Chevrolet, it goes through a 4 plus page detailed explanation of the PS pump and the pressure relief valves and the 2 relief valve springs. Long story short, the small spring and ball c...	admin	1	3311	May 9, 2016 by 51 Styline
	Tire sizes (Preview) Not a big thing but kind of handy if you need a taller,shorter or wider tire http://www.discounttire.com/dtcs/infoTireMath.do TMJ	toomuchjunk	1	1202	May 8, 2016 by 58chev
	How to choose your Axel Gear Ratio . (Preview)	admin	2	1163	May 5, 2016 by admin
	car specs (Preview) http://www.carnut.com/specs/index.html	henrystoys	0	976	May 2, 2016 by henrystoys
	wheel tech (Preview) https://www.rsracing.com/TechWheel.aspx	henrystoys	0	977	May 2, 2016 by henrystoys
	rear end widths (Preview) http://www.carnut.com/specs/rear.html	henrystoys	0	1067	May 2, 2016 by henrystoys
1 2 > Last» \| Page of 2 sorted by